[May 2018] Ensure Pass 300-135 Exam By Training Lead2pass New PDF Dumps 195q

Ensure Pass 300-135 Exam With Lead2pass New 300-135 Brain Dumps:

https://www.lead2pass.com/300-135.html

QUESTION 41
The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, and FHRP services, a trouble ticket has been operated indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to Isolated the cause of this fault and answer the following questions.
On which device is the fault condition located?

A.    R1
B.    R2
C.    R3
D.    R4
E.    DSW1
F.    DSW2
G.    ASW1
H.    ASW2 Read More …

[April 2018] Latest 300-135 Dumps PDF Free Download In Lead2pass 100% 300-135 Exam Pass Guaranteed 181q

Latest Lead2pass 300-135 Exam Free 300-135 Dumps Download:

https://www.lead2pass.com/300-135.html

QUESTION 21
The following commands are issued on a Cisco Router:

Router(configuration)#access-list 199 permit tcp host 10.1.1.1 host 172.16.1.1
Router(configuration)#access-list 199 permit tcp host 172.16.1.1 host 10.1.1.1
Router(configuration)#exit
Router#debug ip packet 199

What will the debug output on the console show?

A.    All IP packets passing through the router
B.    Only IP packets with the source address of 10.1.1.1
C.    All IP packets from 10.1.1.1 to 172.16.1.1
D.    All IP Packets between 10.1.1.1 and 172.16.1.1

Answer: D
Explanation:
In this example, the “debug ip packet” command is tied to access list 199, specifying which IP packets should be debugged. Access list 199 contains two lines, one going from the host with IP address 10.1.1.1 to 172.16.1.1 and the other specifying all TCP packets from host 172.16.1.1 to 10.1.1.1.

QUESTION 22
What level of logging is enabled on a Router where the following logs are seen?

%LINK-3-UPDOWN: Interface FastEthernet0/1, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface FastEthernet0/1, changed state to up

A.    alerts
B.    critical
C.    errors
D.    notifications

Answer: D
Explanation:
Cisco routers, switches, PIX and ASA firewalls prioritize log messages into 8 levels (0-7), as shown below:

LevelLevel NameDescription
0 Emergencies System is unusable
1 Alerts Immediate action needed
2 Critical Critical conditions
3 Errors Error conditions
4 Warnings Warning conditions
5 Notifications Informational messages
6 Informational Normal but significant conditions
7 Debugging Debugging messages

When you enable logging for a specific level, all logs of that severity and greater (numerically less) will be logged. In this case we can see that logging level of 3 (as seen by the 3 in “LINK-3-UPDOWN”) and level 5 (as seen by the 5 in “LINEPROTO-5-UPDOWN”) are shown, which means that logging level 5 must have been configured. As shown by the table, logging level 5 is Notifications.

QUESTION 23
You have the followings commands on your Cisco Router:

ip ftp username admin
ip ftp password backup

You have been asked to switch from FTP to HTTP. Which two commands will you use to replace the existing commands?

A.    ip http username admin
B.    ip http client username admin
C.    ip http password backup
D.    ip http client password backup
E.    ip http server username admin
F.    ip http server password backup

Answer: BD
Explanation:
Configuring the HTTP Client
Perform this task to enable the HTTP client and configure optional client characteristics. The standard HTTP 1.1 client and the secure HTTP client are always enabled. No commands exist to disable the HTTP client. For information about configuring optional characteristics for the HTTPS client, see the HTTPS-HTTP Server and Client with SSL 3.0, Release 12.2(15)T, feature module.

SUMMARY STEPS
1. enable
2. configure terminal
3. ip http client cache {ager interval minutes | memory {file file-size-limit | pool pool-size-limit}
4. ip http client connection {forceclose | idle timeout seconds | retry count | timeout seconds}
5. ip http client password password
6. ip http client proxy-server proxy-name proxy-port port-number
7. ip http client response timeout seconds
8. ip http client source-interface type number
9. ip http client username username

Reference: HTTP 1.1 Web Server and Client.
http://www.cisco.com/en/US/docs/ios/netmgmt/configuration/guide/nm_http_web.html

QUESTION 24
You have 2 NTP servers in your network – 10.1.1.1 and 10.1.1.2.
You want to configure a Cisco router to use 10.1.1.2 as its NTP server before falling back to
10.1.1.1. Which commands will you use to configure the router?

A.    ntp server 10.1.1.1
ntp server 10.1.1.2
B.    ntp server 10.1.1.1
ntp server 10.1.1.2 primary
C.    ntp server 10.1.1.1
ntp server 10.1.1.2 prefer
D.    ntp server 10.1.1.1 fallback
ntp server 10.1.1.2

Answer: C
Explanation:
A router can be configured to prefer an NTP source over another. A preferred server’s responses are discarded only if they vary dramatically from the other time sources. Otherwise, the preferred server is used for synchronization without consideration of the other time sources. Preferred servers are usually specified when they are known to be extremely accurate. To specify a preferred server, use the prefer keyword appended to the ntp server command. The following example tells the router to prefer TimeServerOne over TimeServerTwo:
Router#config terminal
Enter configuration commands, one per line. End with CNTL/Z.

Router(config)#ntp server TimeServerOne prefer
Router(config)#ntp server TimeServerTwo
Router(config)#^Z

QUESTION 25
The following command is issued on a Cisco Router:

Router(configuration)#logging console warnings

Which alerts will be seen on the console?

A.    Warnings only
B.    debugging, informational, notifications, warnings
C.    warnings, errors, critical, alerts, emergencies
D.    notifications, warnings, errors
E.    warnings, errors, critical, alerts

Answer: C
Explanation:
Cisco routers prioritize log messages into 8 levels (0-7), as shown below:

LevelLevel NameDescription
0 Emergencies System is unusable
1 Alerts Immediate action needed
2 Critical Critical conditions
3 Errors Error conditions
4 Warnings Warning conditions
5 Notifications Informational messages
6 Informational Normal but significant conditions
7 Debugging Debugging messages

When you enable logging for a specific level, all logs of that severity and greater (numerically less) will be logged. In this case, when you enable console logging of warning messages (level 4), it will log levels 0-4, making the correct answer warnings, errors, critical, alerts, and emergencies.

QUESTION 26
Which two of the following options are categories of Network Maintenance tasks?

A.    Firefighting
B.    Interrupt-driven
C.    Policy-based
D.    Structured
E.    Foundational

Answer: BD
Explanation:
Proactive Versus Reactive Network Maintenance:
Network maintenance tasks can be categorized as one of the following:

Structured tasks: Performed as a predefined plan.
Interrupt-driven tasks: Involve resolving issues as they are reported.

QUESTION 27
A customer network engineer has made configuration changes that have resulted in some loss of connectivity. You have been called in to evaluate a switch network and suggest resolutions to the problems.

271
PC2 in VLAN 200 is unable to ping the gateway address 172.16.200.1; identify the issue.

A.    VTP domain name mismatch on SW4
B.    VLAN 200 not configured on SW1
C.    VLAN 200 not configured on SW2
D.    VLAN 200 not configured on SW4

Answer: D

QUESTION 28
A customer network engineer has made configuration changes that have resulted in some loss of connectivity. You have been called in to evaluate a switch network and suggest resolutions to the problems.
281
Which of statement is true regarding STP issue identified with switches in the given topology?

A.    Loopguard configured on the New_Switch places the ports in loop inconsistent state
B.    Rootguard configured on SW1 places the ports in root inconsistent state
C.    Bpduguard configured on the New_Switch places the access ports in error-disable
D.    Rootguard configured on SW2 places the ports in root inconsistent state

Answer: A

300-135 dumps full version (PDF&VCE): https://www.lead2pass.com/300-135.html

Large amount of free 300-135 exam questions on Google Drive: https://drive.google.com/open?id=0B3Syig5i8gpDZmFQVlZDZnpLejA

Maybe you also need:

300-101 exam dumps:  https://drive.google.com/open?id=0B3Syig5i8gpDakxVRXg3aUpmTE0

300-115 exam dumps:  https://drive.google.com/open?id=0B3Syig5i8gpDM0pqaFJWUXVuM2M

[February 2018] Lead2pass Offering New 300-135 Exam PDF And 300-135 Exam VCE Dumps For Free Downloading 137q

Official 300-135 Exam Preparation Download From Lead2pass:

https://www.lead2pass.com/300-135.html

QUESTION 11
Refer to the shown below.

%LINK-3-UPDOWN: Interface Serial0/0, changed state to up
%LINEPROTO-5-UPDOWN: Line protocol on Interface Serial0/0, changed state to up

What statement is correct regarding the output shown in the graphic?

A.    These two log messages will not have a severity level.
They are not errors but are just informational messages.
B.    The first log message is categorized as a warning message.
C.    These messages regarding interface status are normal output and will always be displayed when you exit config mode.
D.    The first log message is an error message with a severity level of 3.
E.    The second message would be shown if the logging console warning command had been issued.

Read More …

[January 2018] Lead2pass Cisco New Exam 300-135 VCE Files Free Instant Download 137q

300-135 Latest Dumps Free Download From Lead2pass:

https://www.lead2pass.com/300-135.html

QUESTION 1
A network administrator is troubleshooting an EIGRP connection between RouterA, IP address 10.1.2.1, and RouterB, IP address 10.1.2.2. Given the debug output on RouterA, which two statements are true? (Choose two.)

Read More …

[2017 New] Lead2pass 300-135 New Questions Free Download (76-90)

2017 August Cisco Official New Released 300-135 Dumps in Lead2pass.com!

100% Free Download! 100% Pass Guaranteed!

Thank you so much Lead2pass. You helped me passing my 300-135 exam easily, 90% of the exam questions from the dump appeared in my exam.

Following questions and answers are all new published by Cisco Official Exam Center: https://www.lead2pass.com/300-135.html

QUESTION 76
The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing schemes, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened DSW1 will not become the active router for HSRP group 10.
Use the supported commands to isolated the cause of this fault and answer the following questions.
What is the solution to the fault condition?

A.    Under the interface vlan 10 configuration enter standby 10 preempt command.
B.    Under the track 1 object configuration delete the threshold metric up 1 down 2 command and enter the threshold metric up 61 down 62 command.
C.    Under the track 10 object configuration delete the threshold metric up 61 down 62 command and enter the threshold metric up 1 down 2 command.
D.    Under the interface vlan 10 configuration delete the standby 10 track1 decrement 60 command and enter the standby 10 track 10 decrement 60 command.

Read More …

[2017 New] Lead2pass 300-135 New Questions Free Download (61-75)

2017 August Cisco Official New Released 300-135 Dumps in Lead2pass.com!

100% Free Download! 100% Pass Guaranteed!

I was very confused about selecting the best practice test website when preparing for my 300-135 certification exam. Luckly, a friend told me about Lead2pass.com. I passed the 300-135 exam from the first try. Excellent website for free exam dumps!

Following questions and answers are all new published by Cisco Official Exam Center: https://www.lead2pass.com/300-135.html

QUESTION 61
The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
What is the solution to the fault condition?

A.    In Configuration mode, using the interface range Fa 1/0/1 – 2, then no switchport port- security interface configuration commands.
Then in exec mode clear errdisable interface fa 1/01 – 2 vlan 10 command
B.    In Configuration mode, using the interface range Fa 1/0/1 – 2, then no switchport port- security, followed by shutdown, no shutdown interface configuration commands.
C.    In Configuration mode, using the interface range Fa 1/0/1 – 2, then no switchport port- security interface configuration commands.
D.    In Configuration mode, using the interface range Fa 1/0/1 – 2, then no switchport port- security interface configuration commands.
Then in exec mode clear errdisable interface fa 1/0/1, then clear errdisable interface fa 1/0/2 commands.

Read More …

[2017 New] Free Downloading 300-135 Exam Dumps PDF From Lead2pass (46-60)

2017 July Cisco Official New Released 300-135 Dumps in Lead2pass.com!

100% Free Download! 100% Pass Guaranteed!

Our dumps have been reviewed and approved by industry experts and individuals who have taken and passed 300-135 exam. Lead2pass will have you prepared to take 300-135 test with high confidence and pass easily. Whether you are looking for 300-135 study guide, 300-135 exam questions, 300-135 exam dump or 300-135 test, Lead2pass.com has you covered.

Following questions and answers are all new published by Cisco Official Exam Center: https://www.lead2pass.com/300-135.html

QUESTION 46
The implementations group has been using the test bed to do a `proof-of-concept’ that requires both Client 1 and Client 2 to access the WEB Server at 209.65.200.241. After several changes to the network addressing, routing scheme, DHCP services, NTP services, layer 2 connectivity, FHRP services, and device security, a trouble ticket has been opened indicating that Client 1 cannot ping the 209.65.200.241 address.
Use the supported commands to isolated the cause of this fault and answer the following questions.
What is the solution to the fault condition?

A.    In Configuration mode, using the interface range Fastethernet 1/0/1 ?2, then switchport mode access vlan 10 command.
B.    In Configuration mode, using the interface range Fastethernet 1/0/1 ?2, then switchport access mode vlan 10 command.
C.    In Configuration mode, using the interface range Fastethernet 1/0/1 ?2, then switchport vlan 10 access command.
D.    In Configuration mode, using the interface range Fastethernet 1/0/1 ?2, then switchport access vlan 10 command.

Read More …

[2017 New] Free Downloading 300-135 Exam Dumps PDF From Lead2pass (31-45)

2017 July Cisco Official New Released 300-135 Dumps in Lead2pass.com!

100% Free Download! 100% Pass Guaranteed!

Whether you are a student attempting to pass 300-135 exam to be eligible for a post-graduate job, or a working professional hoping to improve your work credentials and earn that dream promotion Lead2pass is here to help. We have 300-135 exam dumps and brain dumps, so passing 300-135 exam is not an easy feat.

Following questions and answers are all new published by Cisco Official Exam Center: https://www.lead2pass.com/300-135.html

QUESTION 31
You have been brought in to troubleshoot an EIGRP network. A network engineer has made configuration changes to the network rendering some locations unreachable. You are to locate the problem and suggest solution to resolve the issue.

 

R5 has become partially isolated from the remainder of the network. R5 can reach devices on directly connected networks but nothing else. What is causing the problem?

A.    An outbound distribute list in R3
B.    Inbound distribute lists in R5
C.    An outbound distribute list in R6
D.    Incorrect EIGRP routing process ID in R5

Read More …

[2017 New] Free Downloading 300-135 Exam Dumps PDF From Lead2pass (16-30)

2017 July Cisco Official New Released 300-135 Dumps in Lead2pass.com!

100% Free Download! 100% Pass Guaranteed!

Are you worrying about the 300-135 exam? Lead2pass provides the latest 300-135 braindumps and guarantees you passing 300-135 exam beyond any doubt.

Following questions and answers are all new published by Cisco Official Exam Center: https://www.lead2pass.com/300-135.html

QUESTION 16
Which two statements about the Cisco Aironet Desktop Utility (ADU) are true? (Select two)

A.    The Aironet Desktop Utility (ADU) profile manager feature can create and manage only one profile for the wireless client adapter.
B.    The Aironet Desktop Utility (ADU) can support only one wireless client adapter installed and used at a time.
C.    The Aironet Desktop Utility (ADU) can be used to establish the association between the client adapter and the access point, manage authentication to the wireless network, and enable encryption.
D.    The Aironet Desktop Utility (ADU) and the Microsoft Wireless Configuration Manager can be used at the same time to configure the wireless client adapter.

Read More …

[2017 New] Free Downloading 300-135 Exam Dumps PDF From Lead2pass (1-15)

2017 July Cisco Official New Released 300-135 Dumps in Lead2pass.com!

100% Free Download! 100% Pass Guaranteed!

Amazing,100% candidates have passed the 300-135 exam by practising the preparation material of Lead2pass, because the braindumps are the latest and cover every aspect of 300-135 exam. Download the braindumps for an undeniable success in 300-135 exam.

Following questions and answers are all new published by Cisco Official Exam Center: http://www.lead2pass.com/300-135.html

QUESTION 1
A network administrator is troubleshooting an EIGRP connection between RouterA, IP address 10.1.2.1, and RouterB, IP address 10.1.2.2. Given the debug output on RouterA, which two statements are true? (Choose two.)

A.    RouterA received a hello packet with mismatched autonomous system numbers.
B.    RouterA received a hello packet with mismatched hello timers.
C.    RouterA received a hello packet with mismatched authentication parameters.
D.    RouterA received a hello packet with mismatched metric-calculation mechanisms.
E.    RouterA will form an adjacency with RouterB.
F.    RouterA will not form an adjacency with RouterB.

Read More …